Sensor Division – We Manufacture your Infrared Detectors
At the company’s headquarters in Dresden we develop and manufacture pyroelectric infrared detectors in a large variety and of highest quality. They are used by our customers for high-precision gas analysis as well as for fire and flame detection. Local dedicated subsidiaries support our clients in the United States and in the United Kingdom.
The modular construction system of InfraTec’s pyroelectric detectors consists of approximately 50 standard types and therefore offers optimized solutions for a variety of applications. Detectors with reduced microphonic technology and integrated operational amplifier as well as a new detector family with tuneable filter on MOEMS basis are part of our product range, too.
35 found
Single Channel Detectors
Parameters
Type LIE, LIM: Detectors with standard design
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
Housing TO18, TO46: 5.4 mm in diameter
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
Channel Number of measuring channels
Aperture (mm) Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
Operating modes Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
JFET/OpAmp Integrated signal condition like integrated junction field effect transistors (JFET) for detectors in voltage mode or integrated operational amplifiers (OpAmp) for detectors in current mode.
Thermal Compensation A pyroelectric detector is sensitive to changes in temperature. Changes in ambient temperature have an influence on the measurement signal and shifts the operating point. This effect reduces a thermal compensation. Therefore, each pyroelectric element gets an additional optically inactive element, which compensates for unwanted currents.
Low Micro Patented micromechanical chip attachment (LowMicro) by InfraTec to reduce the effects of interfering impact sounds.
Detectivity* As a key parameter, the specific detectivity D* characterizes the signal-to-noise ratio of infrared detectors.
| Type | Housing | Channel | Aperture (mm) | Operating modes | JFET/OpAmp | Thermal Compensation | Low Micro | Detectivity* | Download further information |
| LIE-200 | TO18 | 1 | ø 2.3 | Current Mode | JFET | No | No | 0.55 | LIE-200 |
| LIE-202 | TO18 | 1 | ø 2.3 | Voltage Mode | JFET | No | No | 4.0 | LIE-202 |
| LIE-216 | TO18 | 1 | ø 2.3 | Voltage Mode | JFET | Yes | No | 3.0 | LIE-216 |
| LIE-316 | TO39 | 1 | 5.0 x 5.0 | Voltage Mode | JFET | Yes | No | 4.0 | LIE-316 |
| LME-302 | TO39 | 1 | 5.0 x 5.0 | Voltage Mode | JFET | No | Yes | 6.0 | LME-302 |
| LME-316 | TO39 | 1 | 5.0 x 5.0 | Voltage Mode | JFET | Yes | Yes | 4.0 | LME-316 |
| LME-335 | TO39 | 1 | 5.0 x 5.0 | Current Mode | OpAmp | Yes | Yes | 6.0 | LME-335 |
| LME-336 | TO39 | 1 | 5.0 x 5.0 | Current Mode | OpAmp | Yes | Yes | 4.0 | LME-336 Single supply operation |
| LME-351 | TO39 | 1 | 5.0 x 5.0 | Current Mode | OpAmp | No | Yes | 1.8 | LME-351 |
| LME-352 | TO39 | 1 | 5.0 x 5.0 | Current Mode | OpAmp | No | Yes | 1.5 | LME-352 Single supply operation |
| LME-501 | TO39 | 1 | 5.0 x 5.0 | Current Mode | none | No | Yes | LME-501 | |
| LME-551 | TO39 | 1 | 5.0 x 5.0 | Current Mode | OpAmp | No | Yes | 2.5 | LME-551 |
Multi Channel Detectors
Parameters
Type LIE, LIM: Detectors with standard design
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
Housing TO18, TO46: 5.4 mm in diameter
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
Channel Number of measuring channels
Aperture (mm) Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
Operating modes Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
JFET/OpAmp Integrated signal condition like integrated junction field effect transistors (JFET) for detectors in voltage mode or integrated operational amplifiers (OpAmp) for detectors in current mode.
Thermal Compensation A pyroelectric detector is sensitive to changes in temperature. Changes in ambient temperature have an influence on the measurement signal and shifts the operating point. This effect reduces a thermal compensation. Therefore, each pyroelectric element gets an additional optically inactive element, which compensates for unwanted currents.
Low Micro Patented micromechanical chip attachment (LowMicro) by InfraTec to reduce the effects of interfering impact sounds.
Detectivity* As a key parameter, the specific detectivity D* characterizes the signal-to-noise ratio of infrared detectors.
| Type | Housing | Channel | Aperture (mm) | Operating modes | JFET/OpAmp | Thermal Compensation | Low Micro | Detectivity* | Download further information |
| LIM-011 | TO8 | 4 | ø 2.5 | Voltage Mode | JFET | No | No | 0.8 | LIM-011 Beamsplitter |
| LIM-054 | TO8 | 4 | 2.8 x 2.8 | Current Mode | OpAmp | No | No | 0.42 | LIM-054 Beamsplitter |
| LIM-214 | TO8 | 4 | ø 9.5 | Voltage Mode | JFET | Yes | No | 4.5 | LIM-214 |
| LIM-314 | TO8 | 4 | ø 9.5 | Voltage Mode | JFET | Yes | No | 3.5 | LIM-314 |
| LMM-244 | TO8 | 4 | ø 9.5 | Current Mode | OpAmp | Yes | Yes | 6.0 | LMM-244 |
| LMM-274 | TO8 | 4 | ø 3.5 | Current Mode | OpAmp | Yes | Yes | 6.0 | LMM-274 Single supply operation |
| LRM-244 | TO8 | 4 | 8.5 x 8.5 | Current Mode | OpAmp | Yes | No | 6.0 | LRM-244 Single supply operation |
| LRM-102 | TO18 | 2 | 3.05 x 2.05 | Voltage Mode | JFET | No | No | 4.0 | LRM-102 |
| LRM-202 | TO18 | 2 | 3.05 x 2.05 | Voltage Mode | JFET | Yes | No | 4.0 | LRM-202 |
| LIM-032 | TO39 | 2 | 2.8 x 2.8 | Voltage Mode | JFET | No | No | 2.9 | LIM-032 Beamsplitter |
| LIM-222 | TO39 | 2 | ø 6.0 | Voltage Mode | JFET | Yes | No | 4.5 | LIM-222 |
| LIM-262 | TO39 | 2 | ø 6.0 | Current Mode | OpAmp | Yes | No | 4.5 | LIM-262 |
| LIM-272 | TO39 | 2 | ø 6.0 | Current Mode | OpAmp | Yes | No | 3.0 | LIM-272 Single supply operation |
| LRM-254 | TO39 | 4 | 5.0 x 5.0 | Voltage Mode | JFET | Yes | No | 4.7 | LRM-254 |
| LRM-284 | TO39 | 4 | 5.0 x 5.0 | Current Mode | OpAmp | Yes | No | 4.0 | LRM-284 Single supply operation |
Extended Detectors
Parameters
Type LIE, LIM: Detectors with standard design
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
Housing TO18, TO46: 5.4 mm in diameter
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
Channel Number of measuring channels
Aperture (mm) Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
Operating modes Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
JFET/OpAmp Integrated signal condition like integrated junction field effect transistors (JFET) for detectors in voltage mode or integrated operational amplifiers (OpAmp) for detectors in current mode.
Thermal Compensation A pyroelectric detector is sensitive to changes in temperature. Changes in ambient temperature have an influence on the measurement signal and shifts the operating point. This effect reduces a thermal compensation. Therefore, each pyroelectric element gets an additional optically inactive element, which compensates for unwanted currents.
Low Micro Patented micromechanical chip attachment (LowMicro) by InfraTec to reduce the effects of interfering impact sounds.
Detectivity* As a key parameter, the specific detectivity D* characterizes the signal-to-noise ratio of infrared detectors.
| Type | Housing | Channel | Aperture (mm) | Operating modes | JFET/OpAmp | Thermal Compensation | Low Micro | Detectivity* | Download further information |
| LIE-312 | TO39 | 1 | ø 5.0 | Voltage Mode | JFET | No | No | 8.0 | LIE-312 1Hz ... 4kHz, metal black coating |
| LIE-312f | TO39 | 1 | ø 5.0 | Voltage Mode | JFET | No | No | 4.5 | LIE-312f 10Hz ... 4kHz, metal black coating |
| LIE-332f | TO39 | 1 | ø 5.0 | Voltage Mode | JFET | No | No | 2.8 | LIE-332f 10Hz ... 4kHz, metal black coating |
Tunable Detectors
Parameters
Type LIE, LIM: Detectors with standard design
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
LME, LMM: Detectors with reduced microphonic effect
LRE, LRM: Detectors with micromechanical frame
LFP: Detectors with tunable Fabry‐Pérot filter
Housing TO18, TO46: 5.4 mm in diameter
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
TO5, TO39: 9.2 mm in diameter
TO8: 15.2 mm in diameter
The number following the hyphen indicates the number of pins.
Channel Number of measuring channels
Aperture (mm) Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
Operating modes Size of the circular or rectangular aperture through which radiation hits the sensitive elements.
JFET/OpAmp Integrated signal condition like integrated junction field effect transistors (JFET) for detectors in voltage mode or integrated operational amplifiers (OpAmp) for detectors in current mode.
Thermal Compensation A pyroelectric detector is sensitive to changes in temperature. Changes in ambient temperature have an influence on the measurement signal and shifts the operating point. This effect reduces a thermal compensation. Therefore, each pyroelectric element gets an additional optically inactive element, which compensates for unwanted currents.
Low Micro Patented micromechanical chip attachment (LowMicro) by InfraTec to reduce the effects of interfering impact sounds.
Detectivity* As a key parameter, the specific detectivity D* characterizes the signal-to-noise ratio of infrared detectors.
| Type | Housing | Channel | Aperture (mm) | Operating modes | JFET/OpAmp | Thermal Compensation | Low Micro | Detectivity* | Download further information |
| LFP-3144C | TO8 | tunable | ø 1.9 | Current Mode | OpAmp | Yes | Yes | 0.036 | LFP-3144C |
| LFP-3850C | TO8 | tunable | ø 1.9 | Current Mode | OpAmp | Yes | Yes | 0.03 | LFP-3850C |
| LFP-5580C | TO8 | tunable | ø 2.0 | Current Mode | OpAmp | Yes | Yes | 0.048 | LFP-5580C |
| LFP-80105C | TO8 | tunable | ø 2.0 | Current Mode | OpAmp | Yes | Yes | 0.04 | LFP-80105C |
| XFP-3137 | TO8 | tunable | ø 1.8 | Current Mode | OpAmp | No | No | 0.03 | XFP-3137 FP Filter in fourth order of interference with PbSe photoresistor |
-
In the Service of Meteorology
A measuring instrument that can determine sound scientific data must be calibrated beforehand. Only then can it output reliable information that is deemed comparable and repeatable. As leading bodies, institutions such as the Physikalisch-Technische Bundesanstalt (PTB) or the National Institute of Standards (NIST) constitute the basis worldwide for the correct calibration of measuring instruments. InfraTec supports the work of PTB and NIST and provide them with detectors such as the LIE-651.
-
SENSOR CHINA Expo & Conference 2018
SENSOR CHINA Expo & Conference 2018Shanghai, China10. - 12. September 2018
Applications of Infrared Detectors
Detector Search
InfraTec offers five different product groups including approximately 50 standard pyroelectric detectors. Choose your suitable infrared detectors with the help of our detailed detector search.
